HVAC & Plumbing Services in Indianapolis, IN

Successfully installed a Carrier 59TP7A080V17--16 Performance 97 Series two-stage gas furnace in the basement utility area. The installation included complete ductwork integration with the new air handler unit, proper venting configuration, and electrical connections to ensure optimal system operation. All components were installed per manufacturer specifications with 10-year limited parts warranty and limited lifetime heat exchanger warranty coverage, and the system was tested and confirmed operational upon completion.

Responded to no-cooling call with water leakage from furnace during AC operation. Upon inspection, identified clogged condensate drain line causing water backup and overflow from the evaporator coil drain pan. Cleared blockage from condensate line, verified proper drainage, and tested system operation to confirm cooling function restored and no further leakage present.

Performed scheduled cooling maintenance on residential air conditioning system. Upon arrival, investigated reported intermittent issue where unit requires power cycling to resume operation, with water accumulation noted near equipment during shutdowns. Connected refrigerant manifold gauges and recorded system pressures and temperatures to evaluate operational performance. Inspected outdoor condenser unit including coil condition, fan operation, and cabinet integrity. Verified refrigerant charge levels and system parameters during run cycle. System was operating normally at time of maintenance with no active faults present. Documented current operating conditions and equipment status for ongoing monitoring of intermittent concern.

Completed full system installation of new air conditioning condenser unit and evaporator coil at residential property. Installed outdoor condensing unit on pad adjacent to home exterior, mounted new evaporator coil in basement utility area with proper ductwork connections to existing plenum system. Performed complete system startup, charged refrigerant lines to manufacturer specifications, and conducted diagnostic testing using gauge manifold to verify proper pressures, temperatures, and system operation across all components.

Performed complimentary second opinion evaluation on residential HVAC system following recommendation from another contractor for complete system replacement. Customer reported air conditioning unit operational but unable to maintain desired temperature during peak cooling demand days. Conducted comprehensive system assessment including temperature differential measurements across evaporator coil, which registered 55.5°F supply air temperature. Inspected ductwork installation in attic space, noting reflective insulation wrapping and overall duct condition. Evaluated furnace installation completed three years prior, as concerns were raised by previous contractor regarding equipment performance. Examined humidifier integration, copper refrigerant lines, and flexible duct connections in mechanical room. Documented system components and operating conditions through photographic evidence for reference. Provided professional assessment findings to customer regarding actual system condition v

Responded to service call for reported water leak from HVAC unit. Upon inspection, found condensate drain line showing signs of blockage with visible dark staining and debris buildup inside the PVC pipe. Examined roof penetration at unit location and noted deteriorated sealing around drain line pass-through with significant rust corrosion present on equipment panel base, indicating prolonged moisture exposure. Documented existing conditions with photos showing compromised drain system and weathered equipment enclosure consistent with unit age over 10 years.

Responded to emergency service call for furnace failure following residential flood damage in basement mechanical room. Assessed existing HVAC system including furnace, air handler, and ductwork for water damage and operational status. Provided comprehensive replacement estimate for new heating and cooling equipment to restore climate control functionality to residence.

Conducted comprehensive site assessment for new geothermal heating and cooling system installation in residential property. Evaluated existing mechanical room configuration, including current water heater, expansion tank, and available space for ground-source heat pump equipment and associated hydronic piping connections. Documented existing HVAC air handling units and ductwork infrastructure to determine integration requirements for geothermal system retrofit.

Conducted comprehensive site assessment to develop maintenance plan for commercial facility. Documented two rooftop air conditioning units and three ceiling-mounted heating units, capturing equipment specifications, installation configurations, and current operating conditions to establish preventive maintenance schedule.

Responded to installation callback to address multiple deficiencies identified by homeowner. Leveled outdoor condensing unit to manufacturer specifications and secured unit properly. Corrected and completed all furnace duct tape applications per code requirements. Secured all loose electrical wiring at disconnect and equipment connections, ensuring proper wire management and support. Removed concrete debris from area surrounding electrical disconnect and cleaned work area. Verified system operation with digital multimeter, confirming proper voltage readings of 230V at unit. Performed final inspection of all corrected items and verified system functionality upon completion.

Completed first seasonal cooling maintenance on residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit and indoor evaporator coil, verifying proper operation of all components including fan motor, compressor, and refrigerant lines. All aluminum fins on evaporator coil found clean with proper spacing, copper refrigerant tubing secure with no visible leaks or damage, and condenser unit operating within normal parameters with adequate airflow through louvers and protective grille.

Responded to warranty callback for condensate drainage leak reported one day after installation. Upon inspection, identified active water leakage from PVC condensate line connections. Verified condensate drain system configuration including primary drain line with proper trap and secondary overflow provisions. Observed significant condensation accumulation on metal ductwork and equipment surfaces indicating active system operation. Repositioned collection container beneath leak point to prevent water damage to hardwood flooring. Inspected all PVC pipe joints, elbows, and glued connections throughout the drainage assembly for proper sealing and alignment. Tightened and resealed affected condensate line fittings to eliminate leak. Verified proper pitch and drainage flow through primary condensate system. Confirmed secondary safety pan and overflow protection functioning as designed. System tested and operating within manufacturer specifications with no further leakage detected at time of

Responded to no cooling complaint on system with furnace replacement completed in November. Previous contractor indicated possible control board failure with no signal being sent to outdoor unit. Upon arrival, discovered heavily soiled air filter with significant dust and debris accumulation restricting airflow throughout system. Filter media showed substantial discoloration and clogging across entire surface area, indicating extended period without replacement. Inspected furnace control board and wiring connections. Verified all wire terminations secure at board including thermostat connections, outdoor unit control wiring, and power supply circuits. Control board displaying normal operation with no fault indicators present. Tested voltage output to outdoor unit and confirmed proper 24VAC signal being sent from board. Replaced severely restricted air filter with new filter to restore proper system airflow. Cycled system through cooling mode and verified outdoor unit receiving proper

Responded to callback for water leak on recently installed HVAC system. Upon arrival, inspected air handler unit and condensate drain system. Found condensate drain line improperly pitched, preventing proper drainage and causing water accumulation. Corrected PVC drain line configuration, ensuring proper slope for gravity drainage. Verified condensate pump operation and tested system under cooling mode to confirm water is draining correctly through drain line without leaks. Unit now operating properly with no water leakage detected.

Responded to no cooling call for west wing units at commercial facility. Upon arrival, contacted customer via landline as requested. Inspected thermostat showing 73°F setpoint and measured supply air temperature at 55°F from affected units. Diagnosed cooling system operation and identified issues preventing proper temperature control in west wing zone.

Completed first seasonal cooling maintenance service for 2026. Performed comprehensive inspection of outdoor condensing unit, verified proper operation of all components, and documented equipment condition through photographic records. Accessed attic space to inspect indoor air handling components and electrical connections, confirming system is operating within manufacturer specifications and ready for the cooling season.

Completed AC tune-up on outdoor condenser unit. Unit was found operating with protective cage installed and positioned in confined space with surrounding vegetation. Inspected condenser coil and identified significant accumulation of dirt, dust, and biological growth across fin surfaces, causing reduced heat transfer efficiency. Performed standard maintenance procedures including system inspection and operational checks. Unit is functional but coil contamination may impact cooling performance if not addressed in future service.

Performed comprehensive cooling maintenance on outdoor condensing unit. Conducted electrical diagnostics using digital multimeter to verify proper voltage and amperage readings at the unit's control panel and junction box. Inspected condenser fan assembly, noting visible rust and weathering on protective grille consistent with normal outdoor exposure. Verified fan motor operation and assessed overall system condition. All electrical measurements were within acceptable parameters for continued operation.

Completed full HVAC system installation including Carrier FE5BNXB24L00 furnace with 8KW heat kit, 27VNA324A003 air conditioning unit, and SYSTXCCITC01-C thermostat in utility closet. Reused existing refrigerant linesets after performing complete system flush to remove contaminants. Installed new 1210 media filter for improved air quality, new pad-mounted disconnect switch, and electrical whip for proper power connection. Mounted filter drier on refrigerant lines with service ports for future maintenance access. Installed condensate drain pan with PVC trap configuration and connected drain lines to prevent water damage. Verified all electrical connections, refrigerant line connections, and tested system operation. System is covered under 10-year parts warranty and 1-year labor warranty.

Responded to service call for newly installed unit experiencing freeze-up and inadequate temperature control. Instructed occupant to power down system and operate fan only to prevent further ice accumulation on evaporator coil. Upon inspection, documented crawlspace installation conditions showing evidence of significant moisture infiltration and water staining on structural members surrounding ductwork, which may contribute to ongoing humidity issues affecting system performance. Photographed evaporator coil assembly displaying dust accumulation on fins and insulation placement in mechanical space. Recommended allowing adequate thaw time before conducting diagnostic assessment of refrigerant charge, airflow restrictions, and potential drainage issues to determine root cause of freeze condition.