HVAC & Plumbing Services in Indianapolis, IN

Completed comprehensive Super Tune-Up service on residential HVAC system. Performed electrical diagnostics using digital multimeter to verify proper voltage and amperage at the air handler's wiring compartment, confirming all electrical connections were secure and within manufacturer specifications. Verified Carrier thermostat operation showing system maintaining 72°F setpoint with hold function active and 57% humidity level displayed; confirmed thermostat communication and control functions operating correctly.

Conducted on-site evaluation of a commercial water heater experiencing leakage from the drain pan in a mechanical room. Assessed the existing white cylindrical water heater unit and surrounding infrastructure, including electrical disconnect switch labeled for electric water heater with proper conduit connections. Documented equipment specifications and spatial constraints in the confined utility area, noting the presence of adjacent cylindrical tanks and limited clearance between components. Provided estimate for complete water heater replacement with a 220-volt unit and step-down transformer as requested to meet the facility's electrical requirements.

Completed monthly cooling maintenance on HVAC system, which included replacing heavily soiled air filter that showed significant dust and debris accumulation across all horizontal slats and frame elements. Inspected blower wheel assembly and noted dust buildup on squirrel cage fan blades and housing, though all mechanical components remain intact and functional.

Responded to no cooling complaint on unit less than 10 years old that had been cycling intermittently with visible frost accumulation on evaporator coil. Upon inspection, found outdoor condenser coil heavily contaminated with dirt, dust, and debris buildup restricting airflow, which caused reduced system capacity and evaporator freezing. Documented condition of condenser unit showing significant maintenance neglect with substantial contamination between cooling fins and surrounding landscaping encroachment.

Completed scheduled cooling system maintenance on residential outdoor condensing unit. Performed comprehensive inspection of electrical components, control board, terminal connections, and wiring systems with access panel removed. Verified proper operation of blower motor assembly, checked all wire connections and terminals for security, and documented unit condition. System operating within normal parameters upon completion of preventive maintenance procedures.

# Cooling Maintenance Service Completed Performed comprehensive first cooling maintenance visit under prepaid maintenance agreement. Inspected 16x20x1 pleated air filter at indoor air handler, which showed acceptable condition with minimal debris accumulation. Customer responsible for filter replacement as filters not included in maintenance plan coverage. Conducted exterior equipment inspection revealing significant rust corrosion on electrical disconnect panel and interior components. Heavy oxidation present on metal surfaces of disconnect box, indicating prolonged moisture exposure and weathering. Electrical connections and conduit entry points examined. Disconnect remains functional despite cosmetic deterioration, though corrosion may compromise long-term component integrity. Completed standard cooling season preventive maintenance checklist including visual inspection of condensing unit, electrical connections, and refrigerant lines. System operational at time of service. Recom

# HVAC Cooling System Maintenance Completed comprehensive cooling system maintenance inspection on residential HVAC unit. Performed thorough evaluation of air handler assembly, including interior ductwork inspection revealing properly sealed joints with foam insulation and normal dust accumulation on interior surfaces. Conducted electrical diagnostics using digital multimeter, recording system voltage readings of 506.13V with current draw of 0.133A and temperature reading of 03°C, confirming proper electrical performance within manufacturer specifications. Inspected copper refrigerant lines, wiring connections including ground, neutral, and control wiring, and verified all components operating normally with no immediate service requirements identified.

Completed first tune-up maintenance on HVAC system following November installation. Performed electrical diagnostics using clamp meter to verify proper amperage draw and voltage readings at compressor capacitor and control circuits. Inspected control board connections, verified all wiring terminations secure, and confirmed proper system operation.

Completed comprehensive cooling maintenance on two HVAC systems including inspection of condenser units and evaporator coils. Inspected condenser coil fins for cleanliness and airflow obstruction, noting minor surface corrosion on housing but coils remain operational. Examined evaporator coil assembly within air handler, verified proper refrigerant line connections, and inspected condensate drain pan for proper drainage.

Conducted on-site evaluation of existing 15-year-old furnace system in basement utility area and provided comprehensive replacement estimate. Assessed current equipment condition, including furnace unit with PVC venting configuration, ductwork connections, and air filtration system. Documented existing installation setup with photographs showing furnace placement, associated piping, and mechanical components to support replacement recommendations previously made during prior service visit.

Responded to no-cool complaint with reported water leakage and floor dripping. Upon inspection, discovered significant corrosion and oxidation on copper refrigerant lines with deteriorated foam insulation, along with heavy dirt and debris accumulation on evaporator coil fins. Documented system condition showing advanced wear patterns consistent with drainage issues, likely caused by clogged condensate drain line allowing water to overflow onto floor, and noted corroded refrigerant piping requiring attention to prevent future refrigerant leaks.

Responded to no cooling complaint with thermostat reading 77 degrees. Upon arrival, performed system diagnostics and temperature measurements at supply and return locations. Supply air temperature measured 53°F and return air temperature measured 33.8°F, indicating system is operating within normal parameters and providing adequate cooling with proper temperature split of approximately 19 degrees across the evaporator coil.

Responded to callback for heat pump system running continuously without reaching setpoint temperature. Replaced air filter and performed thermostat troubleshooting to restore unit operation. Connected manifold gauges to outdoor condensing unit to evaluate refrigerant charge levels and system pressures, documenting readings with photos for further analysis of potential refrigerant deficiency affecting cooling capacity.

Completed comprehensive A/C tune-up on residential split system. Performed full inspection of outdoor condenser unit including fan motor operation, refrigerant pressures, electrical connections, and capacitor testing. Inspected indoor air handler, verified control board functionality, checked all wiring connections, and confirmed proper airflow through evaporator coil. All components found operating within manufacturer specifications with no deficiencies noted. System running efficiently and ready for cooling season.

Performed cooling maintenance on HVAC system. Investigated reported water puddle near unit and inspected condensate drainage system for blockages or leaks. Took temperature and humidity readings on supply ductwork using digital instruments to verify proper system operation and diagnose potential condensation issues on insulated duct lines.

Completed comprehensive AC tune-up on commercial unit, performing electrical diagnostics with multimeter to verify proper voltage and frequency readings at 28.9V and 60Hz. Inspected and tested capacitor, circuit board connections, and all electrical components within the condenser unit to ensure optimal system performance and reliability.

Completed comprehensive air conditioning tune-up including electrical system diagnostics and performance verification. Utilized Fluke 323 clamp meter and Fluke 116 multimeter to measure system voltage at 324.6V and confirm proper electrical operation within manufacturer specifications. All tested components operating within normal parameters.

Performed comprehensive heating system maintenance on residential HVAC unit. Conducted electrical diagnostics using clamp meter to verify proper amperage draw on system components, recording readings of 4.3 AAC and 0.6 AAC at various test points. Inspected capacitor connections and contactor assembly, verifying all wire terminations were secure and properly seated. Tested electrical components including relay operation and control circuit functionality. All measurements fell within manufacturer specifications, confirming system is operating efficiently and ready for heating season. Membership renewal was processed on-site as requested, with scheduling accommodations made per household requirements.

Responded to no cooling complaint on Bryant rooftop unit serving office spaces above machine shop. Upon arrival, performed diagnostic testing of electrical components and control board. Used Fieldpiece SC680 meter to measure voltage and verify proper electrical readings at control panel. Inspected circuit boards, wiring connections, and electrical components within control compartment. All measurements indicated system was operating within normal parameters at time of service call.

Installed Honeywell Home ProSeries T6 digital thermostat to replace existing Nest unit. Verified proper wiring connections at terminal block including Y1, Y2, G, OB, Rc, W1, and W2 terminals. Tested system operation to confirm HVAC unit now cycles on properly and thermostat communicates correctly with equipment.