Heating, Cooling & Plumbing Services in Greenwood, IN

Completed preventive maintenance and tune-up on a 1-year-old ground-level cooling system located in garage. Inspected and documented system temperatures using pipe clamp thermometer, evaluated refrigerant levels and operational parameters, and replaced dirty air filter with accumulated dust and debris. All system components operating within normal specifications upon completion of scheduled maintenance service.

Returned to site for scheduled follow-up to address ongoing system issues. Documented geothermal system pressures using Geo-Flo gauge, which showed approximately 20 PSI during initial reading and 0 PSI on secondary check. Coordinated with technical support to troubleshoot recurring performance problems and determine next steps for system resolution.

Completed monthly cooling maintenance on residential HVAC system. Performed temperature measurements at supply plenum, recording 83°F readings using digital thermometer. Conducted electrical diagnostics with multimeter to verify system amperage and voltage levels at equipment. Inspected foil-faced ductwork insulation for integrity and proper sealing. All measurements within normal operating parameters and system operating as designed.

Performed comprehensive air conditioning tune-up on dual outdoor condensing units, completing all standard maintenance procedures including electrical component inspection, capacitor testing, and system performance verification. Enrolled system in preventative maintenance program to ensure ongoing optimal performance and equipment longevity.

Completed comprehensive cooling system maintenance inspection and performance verification. Utilized digital temperature measurement instrumentation to assess system operating parameters and verify proper refrigerant temperatures throughout the cooling cycle. All measurements recorded within manufacturer specifications, confirming optimal system performance and efficiency for the cooling season.

Performed comprehensive AC tune-up on outdoor condensing unit, including electrical diagnostics using digital clamp meter to verify proper amperage draw and voltage readings on compressor and condenser fan motor. All electrical connections were inspected, system operating parameters measured and confirmed within manufacturer specifications, and unit found to be functioning properly with no issues detected.

Completed annual cooling maintenance on 1-year-old ground-mounted AC unit located at laundry room. Performed comprehensive clean and check procedures including inspection of all major components, electrical connections, refrigerant levels, and system operation. Replaced accordion-style pleated air filter per customer request, which showed moderate dust accumulation consistent with normal usage. Inspected exterior electrical disconnect box mounted on brick wall and confirmed proper operation. System operating within normal parameters with no deficiencies noted.

Completed full HVAC system installation in residential utility room, including Carrier furnace and air handler assembly. Installed gray metal furnace cabinet with integrated digital LED display and control panel, mounted metallic air handler unit above furnace, and established all electrical connections with proper color-coded control wiring. Routed and secured flexible ductwork from air handler, installed white PVC condensate drainage and venting piping per manufacturer specifications for high-efficiency system operation. Verified all manufacturer labels and specification plates properly affixed to equipment, confirmed digital display functionality, and ensured all utility connections properly secured and operational.

Responded to no cooling complaint on residential HVAC system less than 10 years old. Performed diagnostic evaluation of unit, measured refrigerant temperatures showing 32.5°F reading at evaporator coil, and inspected air filtration system which showed accumulated debris and restricted airflow. Filter replacement recommended to restore proper system performance and adequate cooling capacity.

Responded to no cooling call on residential HVAC system with indoor temperature reading 78°F against setpoint of 70°F. Performed diagnostic inspection of air handler unit and associated refrigerant lines in basement utility area. Verified system operation, checked refrigerant line integrity including insulated sections, and inspected ductwork connections. Addressed customer inquiry regarding TurboMax feature from previous residence and explained current system capabilities and features.

Responded to service call for heat pump system with inadequate cooling performance. Upon arrival, found unit operational but struggling to maintain temperature setpoint of 74°F with indoor temperature reading 79°F. Conducted system diagnostic and temperature measurements using calibrated digital instrumentation. Visual inspection revealed significant corrosion on equipment components and mounting brackets, with rust staining evident on ventilation panels. Documented equipment condition through photographic evidence showing deteriorated metal supports and oxidation on cabinet surfaces. The corrosion observed indicates prolonged exposure to moisture and potential airflow restrictions through ventilation openings. System requires further evaluation to determine extent of component degradation and impact on cooling efficiency.

Conducted on-site evaluation for residential heating system conversion from forced air to radiant heating. Assessed existing HVAC infrastructure and building layout to determine feasibility and requirements for radiant heating installation. Documented current system configuration and provided comprehensive estimate for complete heating system replacement.

Completed underground fuel tank decommissioning by pumping out all remaining fuel, filling tank with sand for permanent abandonment, and cutting fill and vent lines to below grade level per code requirements. Excavated and accessed tank at residential property, ensuring proper disposal of extracted fuel and complete sand fill to eliminate future collapse hazards. Restored disturbed soil areas and completed site cleanup following tank abandonment procedures.

Responded to no cooling complaint with thermostat displaying error code 179. Diagnosed communication fault between thermostat and HVAC system. Troubleshot wiring connections, verified thermostat functionality, and restored proper system operation with unit now actively cooling to setpoint.

Responded to no cooling call on unit less than 10 years old. Diagnosed failed compressor and confirmed part warranty coverage. Successfully replaced compressor, evacuated and recharged system to manufacturer specifications, and verified proper operation with normal temperatures and pressures restored.

Completed first cooling maintenance service on residential HVAC system. Performed comprehensive inspection of furnace unit and AprilAire air filtration system, verified thermostat operation showing proper temperature control at 70°F, and inspected all PVC condensate drainage lines and connections for proper operation.

Completed routine maintenance inspection on residential cooling system. Performed visual assessment of outdoor condenser unit, confirmed fan assembly and protective grille in proper working condition, and conducted electrical diagnostics using clamp meter to verify amperage draw of 5.79 amps, indicating normal operating parameters for the compressor circuit.

Responded to no cooling complaint with thermostat reading 78°F. Upon arrival, performed diagnostic testing of the HVAC system using digital multimeter to measure electrical values at the outdoor unit. Checked compressor amperage, capacitor functionality, and verified proper voltage supply to all major components. System components including capacitor and electrical connections were inspected and tested to identify the root cause of the cooling failure.

Completed 2026 cooling maintenance first service on two HVAC systems. Performed comprehensive maintenance including cleaning of electrostatic filters as requested, inspected Trane unit with CleanEffects air filtration system showing proper operational status on digital display, and documented significant contamination and deterioration of ductwork insulation with visible mold or dirt accumulation requiring future attention. All routine maintenance tasks completed per service protocol, systems operational, photographic documentation captured for service records.

Provided comprehensive HVAC system replacement estimate for residential property experiencing inadequate cooling performance. Evaluated existing XR17 outdoor condensing unit and indoor furnace system with connected humidifier and assessed refrigerant lines, electrical connections, and ductwork configuration. Documented current equipment specifications and presented replacement options to address system's inability to maintain desired temperature setpoints.