Heating, Cooling & Plumbing Services in Greenwood, IN

Completed annual cooling maintenance on 1-year-old ground-mounted AC unit located at laundry room. Performed comprehensive clean and check procedures including inspection of all major components, electrical connections, refrigerant levels, and system operation. Replaced accordion-style pleated air filter per customer request, which showed moderate dust accumulation consistent with normal usage. Inspected exterior electrical disconnect box mounted on brick wall and confirmed proper operation. System operating within normal parameters with no deficiencies noted.

Completed full HVAC system installation in residential utility room, including Carrier furnace and air handler assembly. Installed gray metal furnace cabinet with integrated digital LED display and control panel, mounted metallic air handler unit above furnace, and established all electrical connections with proper color-coded control wiring. Routed and secured flexible ductwork from air handler, installed white PVC condensate drainage and venting piping per manufacturer specifications for high-efficiency system operation. Verified all manufacturer labels and specification plates properly affixed to equipment, confirmed digital display functionality, and ensured all utility connections properly secured and operational.

Responded to no cooling complaint on residential HVAC system less than 10 years old. Performed diagnostic evaluation of unit, measured refrigerant temperatures showing 32.5°F reading at evaporator coil, and inspected air filtration system which showed accumulated debris and restricted airflow. Filter replacement recommended to restore proper system performance and adequate cooling capacity.

Responded to no cooling call on residential HVAC system with indoor temperature reading 78°F against setpoint of 70°F. Performed diagnostic inspection of air handler unit and associated refrigerant lines in basement utility area. Verified system operation, checked refrigerant line integrity including insulated sections, and inspected ductwork connections. Addressed customer inquiry regarding TurboMax feature from previous residence and explained current system capabilities and features.

Responded to service call for heat pump system with inadequate cooling performance. Upon arrival, found unit operational but struggling to maintain temperature setpoint of 74°F with indoor temperature reading 79°F. Conducted system diagnostic and temperature measurements using calibrated digital instrumentation. Visual inspection revealed significant corrosion on equipment components and mounting brackets, with rust staining evident on ventilation panels. Documented equipment condition through photographic evidence showing deteriorated metal supports and oxidation on cabinet surfaces. The corrosion observed indicates prolonged exposure to moisture and potential airflow restrictions through ventilation openings. System requires further evaluation to determine extent of component degradation and impact on cooling efficiency.

Conducted on-site evaluation for residential heating system conversion from forced air to radiant heating. Assessed existing HVAC infrastructure and building layout to determine feasibility and requirements for radiant heating installation. Documented current system configuration and provided comprehensive estimate for complete heating system replacement.

Completed underground fuel tank decommissioning by pumping out all remaining fuel, filling tank with sand for permanent abandonment, and cutting fill and vent lines to below grade level per code requirements. Excavated and accessed tank at residential property, ensuring proper disposal of extracted fuel and complete sand fill to eliminate future collapse hazards. Restored disturbed soil areas and completed site cleanup following tank abandonment procedures.

Responded to no cooling complaint with thermostat displaying error code 179. Diagnosed communication fault between thermostat and HVAC system. Troubleshot wiring connections, verified thermostat functionality, and restored proper system operation with unit now actively cooling to setpoint.

Responded to no cooling call on unit less than 10 years old. Diagnosed failed compressor and confirmed part warranty coverage. Successfully replaced compressor, evacuated and recharged system to manufacturer specifications, and verified proper operation with normal temperatures and pressures restored.

Completed first cooling maintenance service on residential HVAC system. Performed comprehensive inspection of furnace unit and AprilAire air filtration system, verified thermostat operation showing proper temperature control at 70°F, and inspected all PVC condensate drainage lines and connections for proper operation.

Completed routine maintenance inspection on residential cooling system. Performed visual assessment of outdoor condenser unit, confirmed fan assembly and protective grille in proper working condition, and conducted electrical diagnostics using clamp meter to verify amperage draw of 5.79 amps, indicating normal operating parameters for the compressor circuit.

Responded to no cooling complaint with thermostat reading 78°F. Upon arrival, performed diagnostic testing of the HVAC system using digital multimeter to measure electrical values at the outdoor unit. Checked compressor amperage, capacitor functionality, and verified proper voltage supply to all major components. System components including capacitor and electrical connections were inspected and tested to identify the root cause of the cooling failure.

Completed 2026 cooling maintenance first service on two HVAC systems. Performed comprehensive maintenance including cleaning of electrostatic filters as requested, inspected Trane unit with CleanEffects air filtration system showing proper operational status on digital display, and documented significant contamination and deterioration of ductwork insulation with visible mold or dirt accumulation requiring future attention. All routine maintenance tasks completed per service protocol, systems operational, photographic documentation captured for service records.

Provided comprehensive HVAC system replacement estimate for residential property experiencing inadequate cooling performance. Evaluated existing XR17 outdoor condensing unit and indoor furnace system with connected humidifier and assessed refrigerant lines, electrical connections, and ductwork configuration. Documented current equipment specifications and presented replacement options to address system's inability to maintain desired temperature setpoints.

Completed quoted HVAC repair work in attic mechanical space. Installed new flexible ductwork with proper insulation wrapping and secured all connections with metal strapping per code requirements. System tested and verified operational upon completion.

Completed comprehensive AC tune-up on Carrier outdoor condensing unit, including inspection of all major components, refrigerant levels, and electrical connections. Inspected and documented air filter condition showing minimal dust accumulation with filter in acceptable working condition. Enrolled property in new maintenance plan with expanded coverage including dehumidifier equipment for ongoing preventative maintenance.

Performed pre-sale furnace and air conditioning system inspection as requested. Inspected blower motor assembly, electrical connections, and control wiring for proper operation and safety compliance. Secured furnace unit and plenum box mounting per inspection requirements. Cleaned furnace cabinet interior, removing debris and dust accumulation. Replaced air filter with new pleated filter to ensure proper airflow. Documented equipment condition with photos showing blower assembly, motor components, and low-voltage wiring connections. Provided recommendations for additional securing work needed to meet inspection standards.

Completed pre-sale inspection of Bryant furnace and air conditioning system as requested. Performed comprehensive system evaluation of heating equipment in basement, inspecting furnace unit, ductwork connections, PVC venting system, and condensate drainage. Verified proper installation and connections to water heater venting. Conducted exterior AC unit diagnostics using digital multimeter to test electrical components and capacitor functionality. Inspected condenser unit wiring, connections, and overall system operation. Addressed concern regarding damaged vent pipe connected to water heater. Both heating and cooling systems evaluated for proper operation prior to home sale.

Completed comprehensive assessment of existing HVAC system for full replacement estimate. Evaluated current equipment installation in mechanical room, including cylindrical metal plenum with visible condensation issues and associated ductwork configuration. Inspected exterior electrical disconnect mounted on brick wall, noting weathering and rust staining that may require replacement during system upgrade. Documented existing PVC drainage lines, electrical panel connections, and overall system layout to provide accurate replacement specifications. Photographed all critical components and mechanical space conditions to develop detailed proposal for new HVAC system installation.

Completed installation of ductless mini-split system with wall-mounted cassette-style indoor air handler unit. Secured unit to interior wall, ran refrigerant lines and condensate drain, made all electrical connections, and tested system operation to ensure proper functionality. Installation finished successfully with unit operational and ready for use.